Meler PS 20 NON STOP+, Instruction Manual

Page: 47 / 100

MA-5195-ENG PS20 NON STOP+ DRUM UNLOADER MANUAL MELTER OPERATION
4-21
A - Heating options configuration.
B - General settings of the unit.
C - Automatic loading configuration.
D - Access to statistics.
E - Pumping options
Main Menu
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
3,5 V
0 100 50
0
10
5
Volt rpm
1
0,0 0
2
3,0 20
3
4,0 50
4
7,0 60
5
10 100
Pumping
Analog input
HMI : S02001100 v1.0.106
TC : S02200100 v1.0.084
IO : S02102100 v1.0.106
IO : S02101100 v1.0.106
5. Pumping
Menu
1. Heating 2. Settings
3. Charge 4. Statistics
A
C
B
D
E
Configuring speed ramp
For equipment operating in external reference, the display will show the
current pump rotation set point (input reference conversion as per the full
scale and the conversion table).
The conversion table may be programmed with up to 5 points (input voltage
(Voltage) and output speed (RPM)).
By default the table is programmed (0 V = 0 rpm and 10 V = 100 rpm):
Notes on the editable values in the conversion table:
• The value for voltage must always be shown to one decimal place.
• Point 1 is the starting point for the speed ramp, and therefore the
voltage will always be 0, while the value for output RPM is editable.
• The possible values for each point must be equal to or greater than the
value corresponding to the previous point.
• Point 5 is the final point for the speed ramp, and therefore the voltage
will always be 10, while the value for output RPM is editable.
• It is not necessary to program the value for MAXIMUM RPM in this table.
• If, at any point, the maximum value for Voltage = 10 V is entered,
the corresponding values for Vin and RPM at higher points will be
automatically updated according to the value for this point.
• If, at any point, the maximum value is entered, that is, RPM =
MAXIMUM RPM, the corresponding values for RPM at higher points will
be automatically updated to MAXIMUM RPM.