manualshive.com logo in svg

Meatest M133C, Operation Manual

Share
Download
Meatest M133C Operation Manual Download Page 44

MEATEST

 

M133C Electric Power/Energy Calibrator

 

 

 
Operation manual 

44 

3.

 

Beeper 

This parameter enables / disables the signalization of pressed key. Possible states are „Beep On“ 
and „Beep Off“. Press the Select softkey or press in on the rotary knob to set the selected state. 

4.

 

Calibration Password 

This  parameter sets the calibration password. Calibration password is a five-digit number, which 
must  be  entered  to  access  the  calibration  mode.  If  the  calibration  password  is  set  to  0,  this 
information is displayed in the General menu. Other values are displayed as „Secret“. 

You will be prompted to enter the present calibration password (use the numeric keybord and přes 
Enter).  Now  you  can  change  the  calibration  password.  Cursor  buttons,  rotary  knob  or  numeric 
keyboard  allow  to  set  the  value  in  the  range  of  0  to  99999.  Press  the  Write  softkey  to  set  the 
display’s brightness and return to the General menu. 

Note:  It is advisable to write down actual calibration code if changed. If you forget the calibration 
code, you have to send the calibrator to the manufacturer. 

5.

 

Time 

Setting the real time. The parameter can be changed using cursor buttons, rotary knob or numeric 
keyboard. 

6.

 

Date 

Setting  the  date.  The  parameter  can  be  changed  using  cursor  buttons,  rotary  knob  or  numeric 
keyboard. 

7.

 

Device Information 

Viewing the device information. Displays the serial number and software version. 

 

6.2

 

 Interface Menu 

Submenu contains remote control parameters. 

1.

 

Active interface 

Sets  the  type  of  interface  used  to  calibrator’s  remote  control.  By  selecting  an  item  from  the list 
IEEE488, RS232 or Ethernet type can be selected. The calibrator can be remotely controlled only 
using the selected interface.  

2.

 

IEEE488 address 

Sets  the calibrator’s IEEE488 (GPIB) address. Cursor buttons, rotary knob or numeric keyboard 
allow to set the value in the range of 0 to 30. 

Press the Write

 

softkey to set the address and return to the 

Interface menu.

 Address 02 is set by the manufacturer. 

3.

 

Baud rate 

Sets the communication speed of RS232 bus. By selecting an item from the list 1200, 2400, 4800, 
9600, 19200, 38400, 76800 or 115200 Bd can be selected. 

Summary of Contents for M133C





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands