Meatest M133C Operation Manual Download

Page: 136 / 148

MEATEST

M133C Electric Power/Energy Calibrator

Operation manual

136

Wait-to-Continue command

*WAI

Prevents the instrument from executing any further commands or queries until all previous remote
commands have been executed.

Reset

*RST

This command resets the calibrator to its initial status.

Test operation

*TST?

This command launches an internal self-test. Return the self-test result (“0” for pass or “1” for
fail).

Status byte reading

*STB?

This query returns number in range 0 to 255 with information about content of register STB,
which carries the MSS bit status.

Service Request Enable

*SRE <value>

This command sets condition of the Service Request Enable register. Since bit 6 is not used, the
maximum value is 191.

Service Request Enable reading

*SRE?

This query returns the Service Request Enable Register number.

Event Status Register reading

*ESR?

This query returns the contents of the Event Status Register and clears the register.

Summary of Contents for M133C





















































































































































Search results

Summary of Contents for M133C

Reviews:

Related manuals for M133C

Brands by name

Popular brands

Meatest M133C, Operation Manual

Search results

Summary of Contents for M133C

Reviews:

Related manuals for M133C

Brands by name

Popular brands