Lenovo 7X20 Manual Download Page 61

Page: 61 / 226

1. Turn off the server and disconnect it from the power source. You must disconnect the server from AC

power cycle to reset the XCC.

2. After 45 seconds, reconnect the server to the power source and turn on the server.

3. Retry the operation.

•

FQXSPBR4008I: Management Controller [arg1]: Configuration restoration from a file by user [arg2]

failed to start.

This message is for the use case where a user restores a Management Controller configuration from a file
and the restoration fails to start.

Severity: Error
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0138

User Action:

Complete the following steps until the problem is solved:

1. Turn off the server and disconnect it from the power source. You must disconnect the server from AC

power cycle to reset the XCC.

2. After 45 seconds, reconnect the server to the power source and turn on the server.

3. Retry the operation.

•

FQXSPBR400FI: The neighbor group management is [arg1] by user [arg2] from [arg3] at IP address

[arg4].

Neighbor group management is enabled or disabled by user

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0272

User Action:

Information only; no action is required

•

FQXSPBT0007I: No bootable media available for system [ComputerSystemElementName].

This message is for the use case when an implementation has detected a System with No Bootable
Media.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID:
CIM Prefix: PLAT CIM ID: 0286

User Action:

Please ensure bootable media be installed correctly.

•

FQXSPCA0002M: Numeric sensor [NumericSensorElementName] going low (lower critical) has

asserted.

Chapter 3

XClarity Controller events

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands