Lenovo 7X20 Manual Download Page 210

Page: 210 / 226

User Action:

1. Remove A/C from the server and reseat all drives, backplanes, RAID adapters, expanders (if any), and

cables.

2. Ensure device firmware is at the latest level.

3. Retry the test.

4. If the problem persists, contact technical support.

•

FQXPMSD0005M: self-test completed having the servo (and/or seek) test element of the test failed.

Severity: Error

User Action:

1. Remove A/C from the server and reseat all drives, backplanes, RAID adapters, expanders (if any), and

cables.

2. Ensure device firmware is at the latest level.

3. Retry the test.

4. If the problem persists, contact technical support.

•

FQXPMSD0006M: self-test completed having the read element of the test failed.

Severity: Error

User Action:

1. Remove A/C from the server and reseat all drives, backplanes, RAID adapters, expanders (if any), and

cables.

2. Ensure device firmware is at the latest level.

3. Retry the test.

4. If the problem persists, contact technical support.

•

FQXPMSD0007M: Hard Drive(s) not found

Severity: Error

User Action:

1. Remove A/C from the server and reseat all drives, backplanes, RAID adapters, expanders (if any), and

cables.

2. Ensure device firmware is at the latest level.

3. Verify that the same Error is present in BMC or OneCLI inventory log.

4. Retry the test.

5. If the problem persists, contact technical support.

•

FQXPMSD0008M: UEFI is not ready for LXPM to send command to test hard drive.

Severity: Error

User Action:

1. Reboot system and run the test again.

2. If this message is still reported, run the latest version of SMART tool on OS which is open source tool

and could be downloaded from website to check hard drive status.

3. If the problem persists, contact technical support.

•

FQXPMSD0009M: Device error detected when LXPM sent a test command to a hard drive.

206

ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute

Node Messages and Codes Reference

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands