Lenovo 7X20 Manual Download Page 58

Page: 58 / 226

Table 2. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSPPW0047M

Numeric sensor [NumericSensorElementName] going high (upper
critical) has asserted.

Error

FQXSPPW0061M

Sensor [SensorElementName] has transitioned to critical from a less
severe state.

Error

FQXSPPW0063M

Sensor [SensorElementName] has transitioned to critical from a less
severe state.

Error

FQXSPSD0001L

The [StorageVolumeElementName] has a fault.

Error

FQXSPSD0005L

Array [ComputerSystemElementName] is in critical condition.

Error

FQXSPSD0006L

Array [ComputerSystemElementName] has failed.

Error

FQXSPSE4000I

Certificate Authority [arg1] has detected a [arg2] Certificate Error.

Error

FQXSPUN0019M

Sensor [SensorElementName] has transitioned to critical from a less
severe state.

Error

FQXSPUN0020N

Sensor [SensorElementName] has transitioned to non-recoverable
from a less severe state.

Error

FQXSPUN0023N

Sensor [SensorElementName] has transitioned to non-recoverable.

Error

FQXSPUN0047N

Sensor [SensorElementName] has transitioned to non-recoverable.

Error

FQXSPUP0007L

Invalid or Unsupported firmware or software was detected on system
[ComputerSystemElementName].

Error

FQXSPUP4000I

Please ensure that the Management Controller [arg1] is flashed with
the correct firmware. The Management Controller is unable to match
its firmware to the server.

Error

FQXSPUP4003I

[arg1] firmware mismatch internal to system [arg2]. Please attempt to
flash the [arg3] firmware.

Error

FQXSPUP4004I

XCC firmware mismatch between nodes/servers [arg1] and [arg2].
Please attempt to flash the XCC firmware to the same level on all
nodes/servers.

Error

FQXSPUP4005I

FPGA firmware mismatch between nodes/servers [arg1] and [arg2].
Please attempt to flash the FPGA firmware to the same level on all
nodes/servers.

Error

List of XClarity Controller events

This section lists all messages that can be sent from the XClarity Controller.

•

FQXSPBR4000I: Management Controller [arg1]: Configuration restored from a file by user [arg2].

This message is for the use case where a user restores a Management Controller configuration from a file.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0027

User Action:

ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node

Messages and Codes Reference

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands