manualshive.com logo in svg

Lenovo 7X20, Manual

The Lenovo 7X20 user manual is a comprehensive guide designed to help you navigate and maximize the potential of your device. With our quick-start manual, you can swiftly set up your device hassle-free. Download the manual for free at manualshive.com to unlock the full potential of your Lenovo 7X20.

Share
Download
background image

1.  Check Lenovo support site for an applicable service bulletin or UEFI firmware update that applies to 

this error.

2.  A/C cycle the system.

3.  If the problem persists, collect Service Data logs.

4.  Contact Lenovo Support.

• 

FQXSFDD0012I: SATA Hard Drive Error: [arg1] was recovered. 

Severity: Info

User Action:

Information only; no action is required. 

• 

FQXSFDD0012K: SATA Hard Drive Error: [arg1]. 

Severity: Error

User Action:

Complete the following steps:  

1.  Power down the server.

2.  Re-insert SATA Drive to ensure it is fully connected to the backplane.

3.  If the problem persists, collect Service Data logs and contact Lenovo Support.

• 

FQXSFIO0005M: An intra-board UPI failure has been detected on the link between processor [arg1] 

port [arg2] and processor [arg3] port [arg4]. 

Severity: Error

User Action:

Complete the following steps:  

1.  Check Lenovo support site for an applicable service bulletin or firmware update that applies to this 

error.

2.  If the problem persists, collect Service Data logs.

3.  Contact Lenovo Support.

• 

FQXSFIO0006M: An inter-board UPI failure has been detected on the link between processor [arg1] 

port [arg2] and processor [arg3] port [arg4]. 

Severity: Error

User Action:

Complete the following steps:  

1.  Check Lenovo support site for an applicable service bulletin or firmware update that applies to this 

error.

2.  If the problem persists, collect Service Data logs.

3.  Contact Lenovo Support.

• 

FQXSFIO0007M: An error has been detected by the IIO on Bus [arg1]. The value of Global Fatal 

Error Status register is [arg2]. The value of Global Non-Fatal Error Status register is [arg3]. Please 
check error logs for additional downstream device error data. 

Severity: Error

User Action:

Complete the following steps:  

Chapter 4

.

UEFI events

161

Summary of Contents for 7X20



































































































































































































































Reviews:

No comments

Related manuals for 7X20

Taurus Taurus User Manual preview
Taurus
Brand: Taurus Pages: 14
SilverStone LC19 Manual preview
LC19
Brand: SilverStone Pages: 12
Hamlet HXD3CCUU User Manual preview
HXD3CCUU
Brand: Hamlet Pages: 4
VIPowER VPM-6228H User Manual preview
VPM-6228H
Brand: VIPowER Pages: 34
ENERMAX Brick EB308 User Manual preview
Brick EB308
Brand: ENERMAX Pages: 1
Kingston Technology StorCase Technology Data Express DE75i-A User Manual preview
StorCase Technology Data Express DE75i-A
Brand: Kingston Technology Pages: 33
Thecus Thecus N199 Quick Installation Manual preview
Thecus N199
Brand: Thecus Pages: 6
iBUYPOWER HYTE Revolt 3 Manual preview
HYTE Revolt 3
Brand: iBUYPOWER Pages: 32
Emerson SmartCabinet User Manual preview
SmartCabinet
Brand: Emerson Pages: 97
SWR WorkingPro Series Owner'S Manual preview
WorkingPro Series
Brand: SWR Pages: 6
Thermaltake Level 20 User Manual preview
Level 20
Brand: Thermaltake Pages: 16
Fantec QB-35RFEU3 Manual preview
QB-35RFEU3
Brand: Fantec Pages: 15
Diablotek Citadel User Manual preview
Citadel
Brand: Diablotek Pages: 9
Salvus L2 Manual preview
L2
Brand: Salvus Pages: 17
Peavey 03617090 Manual preview
03617090
Brand: Peavey Pages: 12
Natec OYSTER PRO User Manual preview
OYSTER PRO
Brand: Natec Pages: 12
Pulsar ARADIN1 Installation Manual preview
ARADIN1
Brand: Pulsar Pages: 2
CRU RAX 215DC-3QJ Manual preview
RAX 215DC-3QJ
Brand: CRU Pages: 2

Brands by name

Popular brands

Load more brands