Lenovo 7X20 Manual Download Page 149

Page: 149 / 226

User Action:

Information only; no action is required

•

FQXSPUN0047N: Sensor [SensorElementName] has transitioned to non-recoverable.

This message is for the use case when an implementation has detected a Sensor transitioned to non-
recoverable.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Other
SNMP Trap ID: 50
CIM Prefix: PLAT CIM ID: 0530

User Action:

Complete the following steps:

1. Check the Lenovo support site for an applicable service bulletin or firmware update that applies to

this error.

2. Reboot the system.

3. If problem persists, collect Service Data log and Contact Lenovo Support.

4. For 1-2 Processor system:

a. Reduce the compute board/system in error to a minimum configuration; 1 CPU + 1 DIMM. Does

the problem still occur? Yes/No

b. No: Add CPU and/DIMMs one and a time until the error re-occurs. Consider replacing the last

CPU or DIMM that was installed that caused the error.

c. Yes: If there error/problem still exists, swap in one of the other DIMMs and/or CPUs previously

removed in step a. Proceed to add HW one piece at a time to identify the bad CPU or DIMM.

d. If the problem still exist, (trained technician only) replace system board.

e. If problem persists, escalate to next level of support.

5. For 4-8 Processor system:

a. Escalate to a next level of support.

•

FQXSPUN0056G: Sensor [SensorElementName] has asserted.

This message is for the use case when an implementation has detected a Sensor has asserted.

Severity: Warning
Serviceable: No
Automatically notify Support: No
Alert Category: Warning - Other
SNMP Trap ID: 60
CIM Prefix: PLAT CIM ID: 0508

User Action:

Information only; no action is required

•

FQXSPUN0056I: Sensor [SensorElementName] has deasserted.

This message is for the use case when an implementation has detected a Sensor has deasserted.

Severity: Info
Serviceable: No
Automatically notify Support: No

Chapter 3

XClarity Controller events

145

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands