Lenovo 7X20 Manual Download Page 5 | Manualshive

Page: 5 / 226

background image

Chapter 1. Introduction

When attempting to resolve issues with your solution, the best practice is to begin with the event log of the
application that is managing the solution:

• If you are managing the solution from the Lenovo XClarity Administrator, begin with the Lenovo XClarity

Administrator event log.

• If you are using some other management application, begin with the Lenovo XClarity Controller event log.

The event log contains solution hardware events that are recorded by the Lenovo XClarity Controller or by
UEFI. In addition, events can be generated when you perform diagnostic testing on hard drives or memory
through the Lenovo XClarity Provisioning Manager (although these events are not stored in the event log).

Use this section to view the events that can be generated by Lenovo XClarity Controller, UEFI, or the Lenovo
XClarity Provisioning Manager. For each event, a user action is available to help you understand what must
be done to resolve the issue.

Important:

• Lenovo XClarity Controller (XCC) supported version varies by product. All versions of Lenovo XClarity

Controller are referred to as Lenovo XClarity Controller and XCC in this document, unless specified
otherwise. To see the XCC version supported by your server, go to

https://sysmgt.lenovofiles.com/help/

topic/lxcc_frontend/lxcc_overview.html

.

• Lenovo XClarity Provisioning Manager (LXPM) supported version varies by product. All versions of Lenovo

XClarity Provisioning Manager are referred to as Lenovo XClarity Provisioning Manager and LXPM in this
document, unless specified otherwise. To see the LXPM version supported by your server, go to

sysmgt.lenovofiles.com/help/topic/lxpm_frontend/lxpm_product_page.html

© Copyright Lenovo 2017, 2022

1

«
...
3
4
5
6
7
...
»

Summary of Contents for 7X20



































































































































































































































Reviews:

No comments

Related manuals for 7X20

Brand: IBM Pages: 124

Brand: StarTech.com Pages: 12

Brand: Chenbro Pages: 21

Brand: Sharkoon Pages: 13

Brand: Belden Pages: 22

Brand: Niles Pages: 4

Brand: Connectcom Pages: 10

Brand: peerless-AV Pages: 22

Brand: cable matters Pages: 12

Brand: P.Lindberg Pages: 17

Brand: Pulsar Pages: 2

SmartRack SRW18US13

Brand: Tripp Lite Pages: 3

Brand: CRU Dataport Pages: 2

Brand: Rittal Pages: 32

Brand: Safe-t-Cover Pages: 5

NexStar NST-266SU3

Brand: Vantec Pages: 2

NexStar SX NST-203C3-SV

Brand: Vantec Pages: 2

Thunderbolt IB-3101-TB3

Brand: Icy Box Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands