Lenovo 7X20 Manual Download Page 57

Page: 57 / 226

Table 2. Events organized by severity (continued)

Event ID

Message String

Severity

FQXSPSD0002G

Failure Predicted on [StorageVolumeElementName] for array
[ComputerSystemElementName].

Warning

FQXSPUN0009G

Sensor [SensorElementName] has asserted.

Warning

FQXSPUN0018J

Sensor [SensorElementName] has transitioned from normal to non-
critical state.

Warning

FQXSPUN0026G

Device [LogicalDeviceElementName] has been added.

Warning

FQXSPUN0056G

Sensor [SensorElementName] has asserted.

Warning

FQXSPBR4003I

Platform Watchdog Timer expired for [arg1].

Error

FQXSPBR4007I

Management Controller [arg1]: Configuration restoration from a file by
user [arg2] failed to complete.

Error

FQXSPBR4008I

Management Controller [arg1]: Configuration restoration from a file by
user [arg2] failed to start.

Error

FQXSPCA0002M

Numeric sensor [NumericSensorElementName] going low (lower
critical) has asserted.

Error

FQXSPCA0009M

Numeric sensor [NumericSensorElementName] going high (upper
critical) has asserted.

Error

FQXSPCA0011N

Numeric sensor [NumericSensorElementName] going high (upper
non-recoverable) has asserted.

Error

FQXSPCA0017M

Sensor [SensorElementName] has transitioned to critical from a less
severe state.

Error

FQXSPCA0019N

Sensor [SensorElementName] has transitioned to non-recoverable
from a less severe state.

Error

FQXSPIO0003N

A diagnostic interrupt has occurred on system
[ComputerSystemElementName].

Error

FQXSPIO0004L

A bus timeout has occurred on bus [SensorElementName].

Error

FQXSPIO0006N

A software NMI has occurred on system
[ComputerSystemElementName].

Error

FQXSPIO0011N

An Uncorrectable Error has occurred on [SensorElementName].

Error

FQXSPMA0012M

An Over-Temperature Condition has been detected on the
[PhysicalMemoryElementName] on Subsystem
[MemoryElementName].

Error

FQXSPOS4002I

Watchdog [arg1] Failed to Capture Screen.

Error

FQXSPOS4003I

Platform Watchdog Timer expired for [arg1].

Error

FQXSPOS4010I

OS Crash Video Capture Failed.

Error

FQXSPPU0001N

An Over-Temperature Condition has been detected on
[ProcessorElementName].

Error

FQXSPPW0002L

[PowerSupplyElementName] has Failed.

Error

FQXSPPW0007L

[PowerSupplyElementName] has a Configuration Mismatch.

Error

FQXSPPW0035M

Numeric sensor [NumericSensorElementName] going low (lower
critical) has asserted.

Error

Chapter 3

XClarity Controller events

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands