Lenovo 7X20 Manual Download Page 82

Page: 82 / 226

Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0276

User Action:

Information only; no action is required

•

FQXSPIO4002I: GPU Board Status was recovered by [arg1] of [arg1].

This message is for the use case where GPU Board Status was changed.

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: IMM CIM ID: 0277

User Action:

Information only; no action is required

•

FQXSPMA0010J: [PhysicalMemoryElementName] on Subsystem [MemoryElementName]

Throttled.

This message is for the use case when an implementation has detected Memory has been Throttled.

Severity: Warning
Serviceable: Yes
Automatically notify Support: No
Alert Category: System - Other
SNMP Trap ID: 22
CIM Prefix: PLAT CIM ID: 0142

User Action:

Complete the following steps:

1. Check the event log of system management module and xClarity Controller for any fan or cooling

related issues.

2. Make sure that the airflow at the front and rear of the chassis is not obstructed and that fillers are in

place and correctly installed.

3. Make sure that the room temperature is within operating specifications.

4. Make sure that the DIMM baffles are in place if applicable

5. If the problem persists and there are no other DIMMs with the same indication, replace the DIMM.

•

FQXSPMA0012M: An Over-Temperature Condition has been detected on the

[PhysicalMemoryElementName] on Subsystem [MemoryElementName].

This message is for the use case when an implementation has detected an Over Temperature Condition
for Memory that has been Detected.

Severity: Error
Serviceable: Yes
Automatically notify Support: No
Alert Category: Critical - Temperature
SNMP Trap ID: 0
CIM Prefix: PLAT CIM ID: 0146

ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node

Messages and Codes Reference

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands