Lenovo 7X20 Manual Download Page 106

Page: 106 / 226

CIM Prefix: IMM CIM ID: 0125

User Action:

Information only; no action is required

•

FQXSPPP4018I: External throttling occurred .

External throttling occurred

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0126

User Action:

Information only; no action is required

•

FQXSPPP4019I: Power cap throttling occurred.

Power cap throttling occurrred

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: none
SNMP Trap ID:
CIM Prefix: IMM CIM ID: 0127

User Action:

Information only; no action is required

•

FQXSPPP4020I: The measured power value has returned below the power cap value.

Power exceeded cap recovered

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Warning - Power
SNMP Trap ID: 164
CIM Prefix: IMM CIM ID: 0130

User Action:

Information only; no action is required

•

FQXSPPP4021I: The new minimum power cap value has returned below the power cap value.

Minimum Power Cap exceeds Power Cap recovered

Severity: Info
Serviceable: No
Automatically notify Support: No
Alert Category: Warning - Power
SNMP Trap ID: 164
CIM Prefix: IMM CIM ID: 0131

User Action:

102

ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute

Node Messages and Codes Reference

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands