manualshive.com logo in svg

Lenovo 7X20, Manual

The Lenovo 7X20 user manual is a comprehensive guide designed to help you navigate and maximize the potential of your device. With our quick-start manual, you can swiftly set up your device hassle-free. Download the manual for free at manualshive.com to unlock the full potential of your Lenovo 7X20.

Share
Download
background image

Severity: Warning

User Action:

Complete the following steps:  

1.  Check system spec and follow the rules for populating DCPMM in correct order.

2.  If the problem persists, collect Service Data logs.

3.  Contact Lenovo Support.

• 

FQXSFMA0041K: Near Memory/Far Memory ratio (1:[arg1].[arg2]) for Intel Optane DCPMM 

configuration is not in recommended range (1:2 - 1:16). 

Severity: Warning

User Action:

Complete the following steps:  

1.  Validate system’s memory configuration by using the memory configuration tool below: https://dcsc. 

lenovo.com/#/memory_configuration.

2.  Resolve DIMM configuration so that the DCPMM ratio meets firmware requirements, then reboot the 

system.

• 

FQXSFMA0042K: Intel Optane DCPMM is not supported by processor of this system. 

Severity: Error

User Action:

Validate system’s memory configuration by using the memory configuration tool below: https://dcsc. 
lenovo.com/#/memory_configuration. 

• 

FQXSFMA0047M: SPD CRC checking failed on DIMM [arg1]. [arg2] 

Severity: Warning

User Action:

Complete the following steps:  

1.  Perform a virtual reseat or AC cycle the server.

2.  If the problem returns Collect Service Data log.

3.  Contact Lenovo Support.

• 

FQXSFPU0001N: An unsupported processor has been detected. 

Severity: Error

User Action:

Complete the following steps:  

1.  Check Lenovo support site for a firmware update required for this processor and install that update, if 

applicable.

2.  If the problem persists, collect Service Data logs.

3.  Contact Lenovo Support.

• 

FQXSFPU0002N: An invalid processor type has been detected. 

Severity: Error

User Action:

Complete the following steps:  

Chapter 4

.

UEFI events

177

Summary of Contents for 7X20



































































































































































































































Reviews:

No comments

Related manuals for 7X20

Joy-it JT-RD6012-Case1 Quick Start Manual preview
JT-RD6012-Case1
Brand: Joy-it Pages: 8
Sabrent EC-UASP Specification & User Manual preview
EC-UASP
Brand: Sabrent Pages: 7
Kicker KMTES8 Owner'S Manual preview
KMTES8
Brand: Kicker Pages: 16
Velatia ORMAZABAL basic pfu Series General Instructions Manual preview
ORMAZABAL basic pfu Series
Brand: Velatia Pages: 32
BEGA 71 121 Instructions For Use preview
71 121
Brand: BEGA Pages: 2
CommScope BUDI-2S-SP Installation Instruction preview
BUDI-2S-SP
Brand: CommScope Pages: 8
Raidon GR5630-WSB3+ Quick Installation Manual preview
GR5630-WSB3+
Brand: Raidon Pages: 1
TSI Instruments DustTrak 8535 Operation And Maintenance Manual preview
DustTrak 8535
Brand: TSI Instruments Pages: 70
CRU DataPort 41 Manual preview
DataPort 41
Brand: CRU Pages: 2
PairGain HiGain HRE-420 List 1B Manual preview
HiGain HRE-420 List 1B
Brand: PairGain Pages: 16
IBM 4 U Installation Manual preview
4 U
Brand: IBM Pages: 56
GAMDIAS ARGUS E1 Quick Installation Manual preview
ARGUS E1
Brand: GAMDIAS Pages: 14
Calix ODC-120 Installation Manual preview
ODC-120
Brand: Calix Pages: 44
Panduit Panzone PZWMC12P Instruction Manual preview
Panzone PZWMC12P
Brand: Panduit Pages: 7
Zonet ZNS8022 - SOFTARE Manual preview
ZNS8022 - SOFTARE
Brand: Zonet Pages: 21
DataTale 3.5" Portable HDD Enclosure User Manual preview
3.5" Portable HDD Enclosure
Brand: DataTale Pages: 23
MAG FORGE M100A User Manual preview
FORGE M100A
Brand: MAG Pages: 53
D-Link ShareCenter Quattro DNS-345 User Manual preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 384

Brands by name

Popular brands

Load more brands