Lenovo 7X20 Manual Download Page 14

Page: 14 / 226

1. If warning is not de-asserted after several minutes, check all five fans are installed.

2. Reseat fan module a couple of times. If error still persist, replace fan module.

•

04010210: FAN_TACH_1A: Fan sensor, critical event was asserted, reading value %RPM (Threshold

%RPM)

Asserted when Fan tach reading is below error threshold RPM.

Severity: Critical

User Action:

1. If critical is not de-asserted after several minutes, check all five fans are installed.

2. Reseat fan module a couple of times. If error still persist, replace fan module.

•

04010211: FAN_TACH_1B: Fan sensor, critical event was asserted, reading value %RPM (Threshold

%RPM)

Asserted when Fan tach reading is below error threshold RPM.

Severity: Critical

User Action:

1. If critical is not de-asserted after several minutes, check all five fans are installed.

2. Reseat fan module a couple of times. If error still persist, replace fan module.

•

04010212: FAN_TACH_2A: Fan sensor, critical event was asserted, reading value %RPM (Threshold

%RPM)

Asserted when Fan tach reading is below error threshold RPM.

Severity: Critical

User Action:

1. If critical is not de-asserted after several minutes, check all five fans are installed.

2. Reseat fan module a couple of times. If error still persist, replace fan module.

•

04010213: FAN_TACH_2B: Fan sensor, critical event was asserted, reading value %RPM (Threshold

%RPM)

Asserted when Fan tach reading is below error threshold RPM.

Severity: Critical

User Action:

1. If critical is not de-asserted after several minutes, check all five fans are installed.

2. Reseat fan module a couple of times. If error still persist, replace fan module.

•

04010214: FAN_TACH_3A: Fan sensor, critical event was asserted, reading value %RPM (Threshold

%RPM)

Asserted when Fan tach reading is below error threshold RPM.

Severity: Critical

User Action:

1. If critical is not de-asserted after several minutes, check all five fans are installed.

2. Reseat fan module a couple of times. If error still persist, replace fan module.

•

04010215: FAN_TACH_3B: Fan sensor, critical event was asserted, reading value %RPM (Threshold

%RPM)

Asserted when Fan tach reading is below error threshold RPM.

ThinkSystem D2 Enclosure, Modular Enclosure, Modular Enclosure for 6U Configuration and ThinkSystem SD530 Compute Node

Messages and Codes Reference

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands