LC Packings Probot 161403 User Manual Download Page 2 | Manualshive

Page: 2 / 118

background image

ii

D960R3

User’s Manual Probot

Notice: The Probot

™

Micro Fraction Collector is covered by a limited warranty. A

copy of this warranty is included with this manual. The customer is required to
perform routine maintenance as described in the User’s Manual on a periodic
basis to keep the warranty in effect.

All information in this manual is subject to change without notice and does not
represent a commitment on the part of LC Packings, BV.

The material included in this manual is provided to assist users in the operation,
maintenance and repair of the Probot Micro Fraction Collector. It is assumed that

the individual using this manual has sufficient training in the use of analytical
instrumentation and is aware of the potential hazards including (but not limited
to) electrical hazards, chemical solvent hazards and the exposure to pressurized
solvents.

© November 2004, LC Packings, BV - A Dionex Company. All rights reserved.
No part of this manual may be reproduced or transmitted in any form or by any

means without the written permission of LC Packings, BV.

The following are Trademarks or Registered Trademarks of LC Packings - A
Dionex Company: Probot,

µ

Carrier, UltiMate, UltiChrom, FAMOS, Thermos,

Switchos II, Acurate, UZ-View, UV-Booster, FluoBoost, Pepmap, µ-Dumper, µ-
Fluidics, Fusica, Nano Series, Pico Series, µ-Guard, µ-Precolumn, Nano-

Precolumn.

Dionex™ is a Trademark of Dionex Corporation.

CHROMELEON

™

is a Trademark of the Dionex Corporation.

PEEK™ polymer is a Trademark of Victrex plc.
Teflon® is a Registered Trademark of E.I. duPont de Nemours and Company.

Analyst® is a Registered Trademark of Applied Biosystems/MDS Sciex.

HyStar

™

is a Trademark of Bruker-Daltonics Group.

MassLynx

®™

is a Trademark of Waters® Corporation.

Xcalibur® is a Registered Trademark of ThermoFinnigan.

Belkin

TM

and VideoBusII

™

are Trademarks of the Belkin Corporation.

Windows® and Microsoft® are Registered Trademarks of Microsoft Corporation.

Other product names or company names mentioned herein may be the

trademarks of their respective owners.

Printed in the Netherlands.

«
1
2
3
4
...
»

Summary of Contents for Probot 161403























































































































Reviews:

No comments

Related manuals for Probot 161403

Exitronix LEMD Series

Brand: BARRON Pages: 6

STOMAMED COL-160

Brand: Orliman Pages: 12

Brand: Aveo Engineering Pages: 16

Brand: Nady Audio Pages: 2

Brand: Marani Pages: 35

Brand: Zafferano Pages: 28

Brand: Basler Pages: 33

DynaTrap DT1260-TUN

Brand: Dynamic Pages: 4

Brand: Elma Pages: 35

Brand: Qtx Pages: 6

Brand: Fillauer Pages: 12

Brand: lumishore Pages: 13

Brand: Foxfury Lighting Solutions Pages: 17

SystemRoMedic RiseAtlas450

Brand: Handicare Pages: 48

Allen-Bradley PowerFlex 755T Flux Vector Tuning

Brand: Rockwell Automation Pages: 116

Brand: OmniCure Pages: 2

Brand: TC Electronic Pages: 41

Balance Trainer

Brand: BOSU Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands