LC Packings Probot 161403 User Manual Download Page 113

Page: 113 / 118

User’s Manual Probot

D960R3

E-1

APPENDIX E

Installing and Using the
Belkin

™

USB Video Adapter

E.1

Installation of the Belkin

™

VideoBusII

™

Image Capture Device

This appendix describes the installation and the usage of the Belkin USB video

adapter. This adapter is included with the camera option (P/N 160590) that is

available for the Probot Micro Fraction Collector effective November 2004. The

Belkin VideoBusII device serves to connect the video camera to your PC through
a USB port and to display the camera image in a separate µCarrier

™

window on

your PC.

To use the Belkin video adapter and to display the camera image in µCarrier, the

following equipment is required:

•

Probot with built-in camera

•

Carrier V2.0

•

Belkin F5U208 USB VideoBusII Image Capture Device (P/N 163966, supplied

with camera option)

•

BNC cable (supplied with camera option)

•

BNC to Video adapter (P/N 163973, supplied with camera option)

Summary of Contents for Probot 161403























































































































Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands

LC Packings Probot 161403, User Manual

Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands