LC Packings Probot 161403 User Manual Download Page 23 | Manualshive

Page: 23 / 118

background image

Installation and Getting Started

User’s Manual Probot

D960R3

2-3

2.2

Unpacking

When the Probot Micro Fraction Collector is received, carefully unpack the unit

and verify receipt of all components according to the packing list (some

components include sub-packing lists). It is recommended that all packing

materials be saved in the event that it is necessary to return any item to the

factory.

CAUTION

Caution: When lifting the instrument from the shipping container, make sure that

the unit is kept upright. Lift the unit by placing your hands under the instrument.

CAUTION

Caution: The instrument weighs 23 kg. When the unit is being unpacked and

placed on the laboratory bench, take care to ensure that suitable support is
provided at all times.

If there is external damage to the shipping box, the damage should be reported

to the shipping agent and LC Packings upon receipt of the goods. If internal

damage is observed or if any items are missing, this should be reported to the

shipping agent and to LC Packings as soon as it is observed.

CAUTION

Caution: If there is any apparent damage to the instrument, the user should

investigate the nature of the damage before plugging the unit into the mains to
ensure that powering up of the instrument will not create a hazardous condition

or damage internal components. If the damage appears significant, call
LC Packings or its local representative before connecting the unit to the mains.

2.3

Removing Shipping Components

To ensure that the Probot Micro Fraction Collector is not damaged during

shipment, several components are secured before the unit is packed. It is

necessary for the user to remove the brackets securing these items before the

unit is used. The top cover must be removed to access these brackets.

CAUTION

Caution: Do not operate the Probot Micro Fraction Collector with the safety

brackets installed.

CAUTION

Caution: Do not discard the safety brackets. Whenever the instrument needs to

be shipped, the safety brackets must be re-installed to avoid any damage before

the instrument is moved or shipped.

«
...
21
22
23
24
25
...
»

Summary of Contents for Probot 161403























































































































Reviews:

No comments

Related manuals for Probot 161403

Brand: GE Pages: 242

Brand: GE Pages: 24

Brand: Balanced Body Pages: 3

DVCPRO P2 Series

Brand: Panasonic Pages: 32

Brand: Barreto Pages: 20

Brand: Backyard Discovery Pages: 41

Brand: Eaton Pages: 16

Brand: Eaton Pages: 15

Brand: Echo Pages: 6

Pro Attachment Series

Brand: Echo Pages: 28

Brand: Echo Pages: 2

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

Brand: Nederman Pages: 89

Brand: Nederman Pages: 71

Brand: Nederman Pages: 131

Brand: X-Cite Pages: 2

Brand: NARGESA Pages: 37

Brand: NARGESA Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands