LC Packings Probot 161403 User Manual Download Page 103

Page: 103 / 118

User’s Manual Probot

D960R3

D-1

APPENDIX D

The Vacuum Waste Removal
Option

D.1

Overview

This appendix describes the features and usage of the Vacuum Waste Removal

option. This option is provided as a factory installed option only. If your Probot

Micro Fraction Collector does not include this option, contact your local

representative or LC Packings for upgrade information.

The vacuum waste removal option allows the user to remove undesired portions

of the separation (‘waste’) without the need to spot them onto the target. A

vacuum that can be applied draws then the solvent into a waste container.

The vacuum waste removal option includes the following items:

•

Lift magnet

•

Vacuum pump

•

Waste container

•

Tubing and vacuum connectors

To control the vacuum waste removal, event outputs of the UltiMate capillary

HPLC system are used in combination with the peak detection capability of
CHROMELEON

(see also APPENDIX B).

The following sections provide information about how to install the vacuum

waste removal option and show how to setup the µCarrier and the

CHROMELEON software to control the waste removal option of the Probot. All

information provided refers to µCarrier version 2.0 and to CHROMELEON

6.5

SP3.

Note: The Vacuum Waste Removal Option can not be used in conjunction with

the dosage module (e.g. no matrix solution can be added).

Summary of Contents for Probot 161403























































































































Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands

LC Packings Probot 161403, User Manual

Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands