LC Packings Probot 161403 User Manual Download Page 118

Page: 118 / 118

Appendix E

E-6

D960R3

User’s Manual Probot

E.3

Uninstall Instructions

Note: The Belkin VideoBusII device must be plugged in to uninstall it.

Look for any Question or Exclamation marks in front of any of the selections, if

you see one in front of ‘Belkin’ or ‘unknown USB devices’, remove these

selections by right clicking on them and choose

Uninstall

, otherwise continue to

next step.

Leave the adapter plugged into the computer and go to

Start

, and right click

My Computer

and left click on

Properties

Select the

Hardware

Tab and then click on the

Device Manager

button.

Click on the plus sign next to ‘Imaging Devices’. Under this heading you

should see a ‘Belkin USB VideoBus II, Video’.

Right click on the ‘Belkin USB VideoBus II, Video’ and choose

Uninstall

Click on the plus sign next to ‘Sound, video and game controllers’. Under

this heading you should see a ‘Belkin USB VideoBus II, Audio’.

Right click on ‘Belkin USB VideoBus II, Audio’ and choose

Uninstall

Device Manager

and

System Properties

and unplug the adapter from

the computer.

Go to

Start

Run

and type ‘c:\windows\inf’, if this fails you can try

‘c:\winnt\inf’ and click

Scroll through the list of files and locate the files that start with ‘OEM’.

Windows creates an OEM and an OEM.PNF file for every device that you

install to your system. Try locating the highest number OEM, (for example

oem6 and oem6.pnf). If ‘oem6’ was the highest number, double click on the

‘oem6’ and scroll to the bottom and locate any information about Belkin or

Etek. If you find this information, close the file and delete this ‘oem’ and the

‘oem.pnf’ with the same number. You can check the oem right below this

number just in case.

Disconnect the Belkin VideoBusII device and reboot your computer.

The un-installation is complete.

Summary of Contents for Probot 161403























































































































Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands

LC Packings Probot 161403, User Manual

Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands