LC Packings Probot 161403 User Manual Download Page 86

Page: 86 / 118

Appendix A

A-2

D960R3

User’s Manual Probot

To purge the dosage module:

Switch the rotary valve into the PUMP position, remove the syringe (FIGURE

A-2) and push the piston all the way forward to remove any air or solvent

left. Refer to Section 3.3.3 for more information about how to replace the

syringe.

Waste

Reagent

Vials

Syringe Drive

Dosage Module

PUMP

FILL

PURGE

Rotary Valve

Needle
Tee

µ-Tee

FIGURE A-2 Step 1 – Purge the Tubing

Switch the rotary valve into the FILL position and withdraw the reagent

solvent from the vial. Fill the syringe completely and make sure that enough

reagent solvent is in the vial (FIGURE A-3).

Fill

Aux

Reagent

Vials

Syringe Drive

Dosage Module

PUMP

FILL

PURGE

Rotary Valve

Needle

Tee

µ-Tee

FIGURE A-3 Step 2 – Fill the Syringe

Switch the rotary valve into the PUMP position and purge the tube to the

needle (FIGURE A-4).

Summary of Contents for Probot 161403























































































































Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands

LC Packings Probot 161403, User Manual

Search results

Summary of Contents for Probot 161403

Reviews:

Related manuals for Probot 161403

Brands by name

Popular brands