CALIBRATION AND PROGRAMMING
4-15
8.
0,3-SteerMaxLow
– This value is for fault detection
during calibration. Default value = 3000, If the pot
returns a voltage below this value during calibration,
calibration will be unsuccessful. Steer full left.
9.
0,3-SteerMaxCal
- This is the actual value of the
steer pot “steer full left” based on last calibration.
Steer full left.
10.
0,3-SteerCenHi
- This value is for fault detection
during calibration. Default value = 2700, If the pot
returns a voltage higher than this value during
calibration, calibration will be unsuccessful. Steer
center.
11.
0,3-SteerCenLow
- This value is for fault detection
during calibration. Default value = 2000, If the pot
returns a voltage below this value during calibration,
calibration will be unsuccessful. Steer center.
12.
0,3-SteerCenCal
- This is the actual value of the
steer pot “steer center” based on last calibration.
Steer center.
13.
0,3-SteerMinHi
– This value is for fault detection
during calibration. Default value = 1700, If the pot
returns a voltage higher than this value during
calibration, calibration will be unsuccessful. Steer full
right.
14.
0,3-SteerMinLow
- This value is for fault detection
during calibration. Default value = 250, If the pot
returns a voltage below this value during calibration,
calibration will be unsuccessful. Steer full right.
15.
0,3-SteerMinCal
- This is the actual value of the
steer pot “steer full right” based on last calibration.
Steer full right.
Figure 4-20: Steer Profile Screen
Steer Profile Screen
The “STEER PROFILE” screen shot provides featured
parameters for the Plus 1 functions. See Figure 4-20.
Below is provided a definitions list for forklift
parameters: See Figure 4-20.
1.
0,3-STEER_RPM_X1
– Pre defined in software, for
reference only.
2.
0,3-STEER_RPM_X2
– Pre defined in software, for
reference only.
3.
0,3-STEER_RPM_X3
– Pre defined in software, for
reference only.
4.
0,3-STEER_RPM_X4
– Pre defined in software, for
reference only.
5.
0,3-STEER_RPM_X5
– Pre defined in software, for
reference only.
6.
0,3-STEER_RPM_X6
– Pre defined in software, for
reference only.
7.
0,3-STEER_RPM_Y1
– Pre defined in software, for
reference only.
8.
0,3-STEER_RPM_Y2
– Pre defined in software, for
reference only.
9.
0,3-STEER_RPM_Y3
– Pre defined in software, for
reference only.
10.
0,3-STEER_RPM_Y4
– Value set max RPM for
percent of steer angle.
11.
0,3-STEER_RPM_Y5
– Value set max RPM for
percent of steer angle.
12.
0,3-STEER_RPM_Y6
– Value set max RPM for
percent of steer angle.
Summary of Contents for Bendi B40i4
