manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 7

Contents

Electronic Calibration Modules Reference Guide                                                                                            7

Making Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17

1.85 mm, 3.5 mm, 2.4 mm, 2.92 mm, and Type-N Devices . . . . . . . . . . . . . . . . . . . . .  4-17
7 mm Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-17
Final Connection Using a Torque Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-18
Separating Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-21

Handling and Storage  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-22
ECal Kit Storage Box (Option 150) – (N755xA Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4-23

5. Specifications and Characteristics

Specifications: Terminology and Definitions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-1
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-2

Operating Temperature and Accuracy Enhancement . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-2
Barometric Pressure and Relative Humidity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-3

Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-4

8509xD Series. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4
N755xA Series  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
N4431D (3.5 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-8
N4431D (Type-N 50 

Ω

)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-8

N4431D (7-16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-9
N4431D (4.3-10)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-9
N4432D (Type-N 50 

Ω

)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-10

N4433D (3.5 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-10
N469xD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-11

Characteristic Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-14

N755xA Series  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-14
N4431D (3.5 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-15
N4431D (4.3-10)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-15
N4431D (7-16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-16
N4431D (Type-N 50 

Ω

)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-16

N4432D (Type-N 50 

Ω

 – Microwave). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-17

N4433D (3.5 mm – Microwave) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-17
N469xD Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-18

Mechanical Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-21

Pin Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-21
Type-N Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-23

Typical Pin Depth Values  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-26
Supplemental Mechanical Characteristics  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-30

Mechanical Dimensions of the Modules  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-31

Measurement Uncertainty Calculator  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  5-49

Download the Vector Network Analyzer Uncertainty Calculator  . . . . . . . . . . . . . . . . .  5-49

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands