manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 134

 5-28                                                                                Electronic Calibration Modules Reference Guide

Specifications and Characteristics
Typical Pin Depth Values

5-

Table 5-43 2.4 mm Connector Pin Depth Characteristics

Device 

Typical Pin Depth

 

in Millimeters 

 

(10

–4

 inches) 

Measurement Uncertainty

a

 

 

in Millimeters 

 

(10

–4

 inches) 

Observed Pin Depth Limits

 

in Millimeters 

 

(10

–4

 inches) 

2.4 mm ECal Module (N4693D) –0.0025 to –0.0152

 

(–1.0 to –6.0)

+0.0030 to –0.0030

 

(+1.2 to –1.2)

+0.0005 to –0.0182 

 

(+0.2 to –7.2)

2.4 mm Adapter 

0 to –0.0381

 

(0 to –15)

+0.0030 to –0.0030

 

(+1.2 to –1.2)

+0.0030 to –0.0411 

 

(+1.2 to –16.2)

a. Approxi2 sigma to –2 sigma of gage uncertainty based on studies performed at the factory using precision digital 

gages according to recommended procedures.

Table 5-44 1.85 mm Connector Pin Depth Characteristics

Device 

Typical Pin Depth

 

in Millimeters 

 

(10

–4

 inches) 

Measurement Uncertainty

a

 

 

in Millimeters 

 

(10

–4

 inches) 

Observed Pin Depth Limits

 

in Millimeters 

 

(10

–4

 inches) 

1.85 mm ECal Module (N4694D) –0.0025 to –0.0152

 

(–1.0 to –6.0)

+0.0030 to –0.0030

 

(+1.2 to –1.2)

+0.0005 to –0.0182 

 

(+0.2 to –7.2)

1.85 mm Adapter 

0 to –0.0381

 

(0 to –15)

+0.0030 to –0.0030

 

(+1.2 to –1.2)

+0.0030 to –0.0411 

 

(+1.2 to –16.2)

a. Approxi2 sigma to –2 sigma of gage uncertainty based on studies performed at the factory using precision digital 

gages according to recommended procedures.

Table 5-45 7 mm Connector Pin Depth Characteristics

Device 

Typical Pin Depth

 

in Millimeters 

 

(10

–4

 inches) 

Measurement Uncertainty

a

 

 

in Millimeters 

 

(10

–4

 inches) 

Observed Pin Depth Limits

 

in Millimeters 

 

(10

–4

 inches) 

7 mm ECal Module (85091D)

–0.0254 to –0.0508

 

(–10.0 to –20.0) 

+0.0038 to –0.0038

 

(+1.5 to –1.5)

+0.0216 to –0.0546 

 

(+8.5 to –21.5)

7 mm ECal Module (N4696D)

–0.0025 to –0.0152

 

(–1.0 to –6.0) 

+0.0038 to –0.0038

 

(+1.5 to –1.5)

+0.0013 to –0.0190 

 

(+0.5 to –7.5)

a. Approxi2 sigma to –2 sigma of gage uncertainty based on studies performed at the factory using precision digital 

gages according to recommended procedures.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands