manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 70

 3-4                                                                                Electronic Calibration Modules Reference Guide

Operating ECal Module
Setting Up a Calibration

3-

9.

Perform a 1-port calibration by clicking the softkey of the selected port.

10.

Refer to the ENA User’s Guide or Online Help for more details on 

performing various types of 1-port calibrations. Refer to your instrument’s 

Online Help/User’s Guide on 

http://ww.keysight.com

.

11.

When the calibration is complete, remove the ECal module, and connect 

the DUT.

Required Procedure for All Calibrations (FieldFox)

For all calibration types, complete the following steps:

1.

Connect an ECal module to the FieldFox having the appropriate frequency 

range and connector type. 

2.

Wait until LED turns green.

3.

Set up the analyzer in the measurement configuration. Select the 

frequency, power, sweep and other stimulus settings.

4.

View the response (uncorrected) and optimize the analyzer settings as 

needed.

5.

Connect the ECal module to the measurement ports.

6.

Set instrument to frequency range that is compatible with your ECal 

module.

7.

Navigate to 

Cal 5

 > 

Mechanical Cal / ECal

.

For each test port to be calibrated, press the 

Change DUT Connectors

 and 

follow the prompts.

Excessive torque can damage ECal module connectors. See 

Table 4-1 on 

page 4-21

 for the required torque setting for each connector type.

For optimal results, terminate any unused ECal ports with a 50 ohm load.

Verify the FieldFox is set to a frequency range that is within the ECal 

module’s range. If the frequency start and or stop frequency are outside 

the range of the ECal module, the FieldFox does not recognize the ECal 

module.

IMPORTANT

: Until the correct connector-type is selected for your ECal 

module, the ECal module choice(s) will not be visible in the 

Select 

CalKit

 table.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands