manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 100

 4-18                                                                                Electronic Calibration Modules Reference Guide

Use, Maintenance, and Care of the Devices
Making Connections

4-

4.

As you bring one connector up to the other, and as you make the actual 

connection, be sure the connectors align perfectly.

5.

Push the connectors straight together. Do not twist or screw them 

together.

6.

Engage the connector nut over the threads on the second connector. Turn 

only the connector nut. Let the connector nut pull the two connectors 

straight together.

7.

Carefully align the connectors. The male connector center pin must slip 
concentrically into the contact finger of the female connector.

8.

Push the connectors straight together and tighten the connector nut 

finger tight. Do not twist or screw the connector together. As the center 

conductors mate, there is usually a slight resistance

Final Connection Using a Torque Wrench

Using a torque wrench guarantees the connection is not too tight, preventing 

possible connector damage. It also guarantees that all connections are equally 

tight.
Use the recommended torque wrench to make a final connection. 

Table 4-1 on 

page 4-21

 provides information on the torque wrench recommended for use 

with each connector type. 

1.

Turn the connector nut. This may be possible to do by hand if one of the 

connectors is fixed (as on a test port). However, it is recommended that 

you use an open-end wrench to keep the body of the device from turning. 

2.

Position both wrenches within 90 degrees of each other before applying 

force. Wrenches opposing each other (greater than 90 degrees apart) will 

cause a lifting action that can misalign and stress the connections of the 

device involved. This is especially true when several devices are 

connected together. Refer to 

Figure 4-7

. 

IMPORTANT! 

At this point, you want a connection in which the outer 

conductors make gentle contact at all points on both mating surfaces. This 

requires very light finger pressure.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands