Keysight Technologies 85091D Reference Manual Download Page 107

Page: 107 / 172

5- 1

Keysight Electronic Calibration Modules
RF/Microwave Two Port

Reference Guide

Specifications and Characteristics

Specifications: Terminology and Definitions

The following terms and definitions apply to Keysight’s N755xA series of ECal

modules. The definitions are specific to these modules and are not necessarily

valid definitions for other Keysight Technologies products.

Table 5-1 Specifications and Characteristics Terminology

Terms

Definitions

Operating Temperature Range

The temperature range over which the ECal modules maintain conformance to

their specifications.

Error-Corrected Temperature Range

The allowable network analyzer ambient temperature drift during

measurement calibration and during measurements when network analyzer

correction is turned on. It is also the range over which the network analyzer

maintains its specified performance while correction is turned on. If this

temperature range is exceeded, the error-corrected performance of the

network analyzer is degraded.

Measurement Calibration

This calibration determines the corrections necessary for accuracy-enhanced

(correction on) measurements.

Connector Pin Depth Values

Pin depth is a relative measurement value between the center conductor and

outer conductor mating surfaces. All references to pin depth in this manual

treat positive (+) values as protrusions of the center conductor, and negative

(–) values as recessions of the center conductor. See

“Typical Pin Depth

Values” on page 5-26

Electrical Specifications

Warranted performance. Specifications include guard bands to account for the

expected statistical distribution, measurement uncertainties, and changes in

performance due to environmental conditions. Included with Option UK6.

Characteristic Performance

A performance parameter that the product is expected to meet before it leaves

the factory, but is not verified in the field and is not covered by the product

warranty. A characteristic includes the same guard bands as a specification.

Typical Corrected Performance

Expected performance of an average unit which does not include guard bands.

It is not covered by the product warranty.

Summary of Contents for 85091D













































































































































































Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands

Keysight Technologies 85091D, Reference Manual

Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands