manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 132

 5-26                                                                                Electronic Calibration Modules Reference Guide

Specifications and Characteristics
Typical Pin Depth Values

5-

Typical Pin Depth Values

The pin depth value of each device is not specified, but is an important mechanical 

parameter. The electrical performance of the device depends, to some extent, on its 

pin depth. The electrical specifications for each module takes into account the effect of 

pin depth on the device’s performance. The following tables list the typical pin depths 

and measurement uncertainties, and provides observed pin depth limits for the 

devices. If the pin depth of a device does not measure within the observed pin depth 

limits, it may be an indication that the device fails to meet electrical specification. 
Refer to 

Figure 5-2

 and 

Figure 5-5

 for a visual representation of proper pin depth 

(slightly recessed).

Table 5-38 Type-F 75 

Ω

 Connector Pin Depth Characteristics

Device 

Typical Pin Depth

 

in Millimeters 

 

(10

–4

 inches) 

Measurement Uncertainty

a

 

in Millimeters 

 

(10

–4

 inches) 

Observed Pin Depth Limits

 

in Millimeters

 

(10

–4

 inches) 

Type-F 75 

Ω

 ECal Module 

 

(8909xD)

–0.0254 to –0.0508

 

(–1.0.0 to –20.0) 

+0.0038 to –0.0038

 

(+1.5 to –1.5) 

–0.0216 to –0.0546

 

(–8.5 to –21.5)

Type-F 75 

Ω

 Adapter

–0.0127 to –0.0762 

 

(–5.0 to –30.0)

 +0.0038 to –0.0038

 

(+1.5 to –1.5)

+0.0038 to –0.0165

 

(+1.5 to –6.5)

a. Approxi2 sigma to –2 sigma of gage uncertainty based on studies performed at the factory using preci-

sion digital gages according to recommended procedures.

Table 5-39 Type-N 50 

Ω

 Connector Pin Depth Characteristics

Device 

Typical Pin Depth

a,b

 

 

in Millimeters 

 

(10

–4

 inches) 

Measurement Uncertainty

c

 

in Millimeters 

 

(10

–4

 inches) 

Observed Pin Depth Limits

 

in Millimeters

 

(10

–4

 inches) 

Type-N 50 

Ω

 ECal Module 

 

(N755xA)

–0.0508 to –0.3810

 

(–20.0 to –150.0) 

+0.0038 to –0.0038

 

(+1.5 to –1.5) 

–0.0470 to –0.3848

 

(–18.5 to –21.5)

Type-N 50 

Ω

 ECal Module 

 

(N4431D, N4432D)

–0.0254 to –0.0508

 

(–10.0 to –20.0) 

+0.0038 to –0.0038

 

(+1.5 to –1.5) 

–0.0216 to –0.0546

 

(–8.5 to –21.5)

Type-N 50 

Ω

 ECal Module 

 

(N4690D)

–0.0051 to –0.0152

 

(–2.0 to –6.0) 

+0.0038 to –0.0038

 

(+1.5 to –1.5) 

–0.0013 to –0.0190

 

(–0.5 to –7.5) 

Type-N 50 

Ω

 Adapter

0 to –0.0127 

 

(0 to –5.0)

 +0.0038 to –0.0038

 

(+1.5 to –1.5)

+0.0038 to –0.0165

 

(+1.5 to –6.5)

a. Measured from a 5.258 mm (0.207 inches) nominal offset.

b. For N755xA ECals, the Type-N connector is not a precision contact per IEEE precision connector standards.

c. Approxi2 sigma to –2 sigma of gage uncertainty based on studies performed at the factory using preci-

sion digital gages according to recommended procedures.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands