Keysight Technologies 85091D Reference Manual Download Page 80

Page: 80 / 172

3-14 Electronic Calibration Modules Reference Guide

Operating ECal Module
ECal Troubleshooting

ECal Troubleshooting

Table 3-4

8509xD, N469xD/N443xD Troubleshooting

LED Color

Description

Possible Causes

Solutions

Orange

ECal is connected

and functioning, but

is not

communicating with

driver software.

ECal module is connected to an

instrument (or PC) without the

appropriate driver software installed.

Connect the ECal module to a

compatible instrument.
Ensure that the instrument software is

up to date.

Faulty instrument USB port

Connect to a different USB port on the

instrument.

Faulty USB cable

Connect via a different USB cable.

Faulty USB hub

Connect ECal directly to a USB port on

the instrument.

Alternating

Green/Orange

Flashing

ECal is too cold and

unable to regulate

internal temperature

to setpoint.

ECal is too cold and unable to

regulate internal temperature to

setpoint.

Move ECal to a warmer location. Refer

“Environmental Specifications”

on page 5-2

Alternating

Green/Red

Flashing

ECal is too hot and

unable to regulate

internal temperature

to setpoint.

ECal is too hot and unable to regulate

internal temperature to setpoint.

Move ECal to a cooler location. Refer to

“Environmental Specifications” on

page 5-2

Off

The ECal is not

functioning.

ECal is not connected to instrument.

Double check the USB connectors are

firmly inserted.

Faulty instrument USB port

Connect to a different USB port on the

instrument.

Faulty USB cable

Connect via a different USB cable.

Faulty USB hub

Connect ECal directly to a USB port on

the instrument.

Faulty ECal module

Return to Keysight for service. Refer to

Chapter 1

“Service and

Recertification” on page 1-29

Summary of Contents for 85091D













































































































































































Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands

Keysight Technologies 85091D, Reference Manual

Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands