manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 98

 4-16                                                                                Electronic Calibration Modules Reference Guide

Use, Maintenance, and Care of the Devices
Gaging Connectors

4-

Gaging Technique–7 mm Gage

Figure 4-6 

Using a 7 mm Gage

While performing pin depth measurements, use different orientations of the 

gage with the connector. Average a minimum of three readings, each taken 

after a quarter-turn rotation of the gage, to reduce measurement variations 

that result from the gage or the connector face not being exactly perpendicular 

to the center axis.
To zero a gauge, review the instructions in 

“Zeroing Connector Gages” on 

page 4-14

. 

You must remove the collet with the collet extractor tool prior to 

performing pin depth measurements.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands