manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 61

Electronic Calibration Modules Reference Guide                                                                               2-17

Preparing ECal for Use
Options

Options

8509xD Options 

Where:

— Option 00F, configures the module with female-to-female connectors.
— Option 00M, configures the module with male-to-male connectors.
— Option M0F, configures the module with male-to-female connectors.

N755xA Options 

Where “x” represents the connector type (i.e., “N” for 50

Ω

 Type-N and “3” for 

3.5 mm:

— Option xFF, configures the module with female-to-female connectors.
— Option xMM, configures the module with male-to-male connectors.
— Option xMF, configures the module with male-to-female connectors.

N4431D Options 

— Option 010 configures the model with 3.5 mm –f– and 020 configures the 

module with Type-N 50 ohm -f- connectors on all ports.

— Option UK6 adds a commercial calibration certificate with measured data.
— For more, refer to 

“N4431D Modules (RF Four-Port)” on page 1-11

N469xD Options 

Where:

— Option F0F, configures the module with female-to-female connectors.
— Option M0M, configures the module with male-to-male connectors.
— Option M0F, configures the module with male-to-female connectors.

N4432D Options 

— Option 020 configures the module with Type-N 50 ohm -f- connectors on 

all ports.

— Option UK6 adds a commercial calibration certificate with measured data.
— For more, refer to 

“N4432D and N4433D Modules (Microwave Four-Port)” 

on page 1-18

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands