Keysight Technologies 85091D Reference Manual Download Page 11

Page: 11 / 172

Electronic Calibration Modules Reference Guide 1-3

General Information
When to Calibrate

When to Calibrate

A network analyzer calibration remains valid as long as the changes in the

systematic error are insignificant. This means that changes to the uncorrected

leakages (directivity and isolation), mismatches (source match and load

match), and frequency response of the system are small (<10%) relative to

accuracy specifications.
Change in the environment (especially temperature) between calibration and

measurement is the major cause in calibration accuracy degradation. The

major effect is a change in the physical length of external and internal cables.

Other important causes are dirty and damaged test port connectors and

calibration standards. If the connectors become dirty or damaged,

measurement repeatability and accuracy is affected. Fortunately, it is relatively

easy to evaluate the general validity of the calibration. To test repeatability,

remeasure one of the calibration standards. If you can not obtain repeatable

measurements from your calibration standards, maintenance needs to be

performed on the test port connectors, cables and calibration standards. Also,

maintain at least one sample of the device under test or some known device as

your reference device. A verification kit may be used for this purpose. After

calibration, measure the reference device and note its responses. Periodically

remeasure the device and note any changes in its corrected response which

can be attributed to the test system. With experience you will be able to see

changes in the reference responses that indicate a need to perform the

measurement calibration again.

≥

2-Port, data-based, expanded, flush

thru

Characterized

Reflection

Transmission

Internal unknown

Reflection

Transmission

External flush

Reflection

Transmission

≥

2-Port, data-based, expanded,

unknown thru

Characterized

Reflection

Transmission

Internal

unknown

Reflection

Transmission

++ better; + slightly better; = same

a. Flush thru should NOT be used when the test port connectors are not the same type as the calibration standards. SMA and

3.5 mm connectors are mateable but are NOT the same type.

Mechanical Calibration Type

ECal Thru Type

Measurement

ECal

Mechanical

Calibration

Summary of Contents for 85091D













































































































































































Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands

Keysight Technologies 85091D, Reference Manual

Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands