Keysight Technologies 85091D Reference Manual Download Page 75

Page: 75 / 172

Electronic Calibration Modules Reference Guide 3-9

Operating ECal Module
Setting Up a Calibration

— Modify the state settings: allows you to specify the number of data points

(1601 max.) or other stimulus settings the module uses to perform a

calibration.

When you perform a User-Characterization, the factory characterization data

remains stored in the module’s memory. At calibration, you can select the

factory characterization or any of the user-defined characterizations stored in

the module. The module can store up to five user-defined characterizations (in

addition to the factory characterization data).
User-Characterization is currently available with PNA and PXIe. FieldFox

user-characterizations must be performed on a PNA or ENA.
To perform a User-Characterization, a calibration kit (having the same

connector type as the new reference plane) is required.
For detailed information on calibration methods using an PNA or PXIe series

network analyzer or FieldFox, refer to the appropriate user guide or online

Help. To use the Internet to view the PNA or PXIe online Help, use the steps

listed in

“Finding More Information on Performing a Calibration” on

page 3-10

Summary of Contents for 85091D













































































































































































Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands

Keysight Technologies 85091D, Reference Manual

Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands