manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 89

Electronic Calibration Modules Reference Guide                                                                               4-7

Use, Maintenance, and Care of the Devices
Cleaning Connectors

2. Clean the Connector Threads

Moisten (don’t soak) a lint-free swab or cleaning cloth with isopropyl 

alcohol to remove any dirt or stubborn contaminants that cannot be 

removed with compressed air or nitrogen. Refer to 

“Other ECal 

Accessories” on page 6-12

 for cleaning swabs and other connector 

cleaning supplies.

a.

Apply a small amount of isopropyl alcohol to a lint-free swab.

b.

Clean the connector threads.

c.

Let the alcohol evaporate, then blow the threads dry with a gentle 

stream of clean, low-pressure compressed air or nitrogen. Always 

completely dry a connector before you reassemble or use it.

3. Clean the Mating Plane Surfaces

a.

Apply a small amount of isopropyl alcohol to a new lint-free 

cleaning cloth or swab.

b.

Clean the center and outer conductor mating plane surfaces. Refer 

to 

Figure 4-2 on page 4-4

. When cleaning a female connector; use 

short strokes to avoid snagging the swab on the center conductor 

contact fingers.

c.

Let the alcohol evaporate, then blow the mating plane surface dry 

with a gentle stream of clean, low-pressure compressed air or 

nitrogen. Always completely dry a connector before you reassemble 

or use it.

4. Inspect Each Connector

Inspect the connector to make sure that no particles or residue are 

present.

Cleaning 7 mm Connectors

Cleaning the Center Collet While It Is in Place

You do not have to remove the center conductor collet to clean a precision 

7 mm connector.
With the center collet in place:

1.

Place a lint-free cleaning cloth 

fl

at on a table.

Use ONLY isopropyl alcohol to clean connector surfaces. Any other solvent 

may damage the insulators, support beads, and seals in the connector.
Never immerse the connector in solvents of any kind. The solvent can 

become trapped within the assembly and cause SWR, phase, and insertion 

loss problems.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands