Keysight Technologies 85091D Reference Manual Download Page 88

Page: 88 / 172

4-6 Electronic Calibration Modules Reference Guide

Use, Maintenance, and Care of the Devices
Cleaning Connectors

Cleaning Connectors

Clean connector interfaces prolong connector life and produce more accurate
and repeatable measurements.

Cleaning Coax Connectors

1. Use compressed Air or Nitrogen

Use compressed air (or nitrogen) to loosen particles on the connector

mating plane surfaces.
You can use any source of clean, dry, low-pressure compressed air or

nitrogen that has an effective oil-vapor filter and liquid condensation trap

placed just before the outlet hose.
Ground the hose nozzle to prevent electrostatic discharge, and set the air

pressure to less than 414 kPa (60 psi) to control the velocity of the air

stream. High-velocity streams of compressed air can cause electrostatic

effects when directed into a connector. These electrostatic effects can

damage the device. For additional information refer to

“Electrostatic

Discharge” on page 4-1

earlier in this chapter.

Always use protective eyewear when using compressed air or

nitrogen.

The following cleaning procedure can be used for most coaxial connectors.

Keep isopropyl alcohol away from heat, sparks, and flame. Store in a

tightly closed container. Isopropyl alcohol is extremely flammable. In

case of fire, use alcohol foam, dry chemical, or carbon dioxide; water

may be ineffective.

Use isopropyl alcohol with adequate ventilation and avoid contact

with eyes, skin, and clothing. It causes skin irritation, may cause eye

damage, and is harmful if swallowed or inhaled. It may be harmful if

absorbed through the skin.

Wash thoroughly after handling. In case of spill, soak up with sand

or earth. Flush spill area with water.

Dispose of isopropyl alcohol in accordance with all applicable

federal, state, and local environmental regulation.

Summary of Contents for 85091D













































































































































































Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands

Keysight Technologies 85091D, Reference Manual

Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands