manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 71

Electronic Calibration Modules Reference Guide                                                                               3-5

Operating ECal Module
Setting Up a Calibration

8.

Press 

Change Cal Type

. The connected ECal module and relevant User 

Characterizations will appear, with the ECal factory default as the default 

Cal Kit. In the Select Calkit table that opens, verify the correct ECal model 

is selected. If not, use the arrow keys to select the correct ECal model. 

9.

Press 

Finish

10.

 Press 

Start Calibration

.

11.

 In the Calibration Wizard window that opens, press 

Measure

. 

12.

 Continue to follow the prompts for the other port and when the 

calibration is complete, remove the ECal module, and connect the DUT. 

For more information on using an ECal module with the FieldFox, refer to 

the User’s Guide for your model on 

www.keysight.com

.

Excessive torque can damage ECal module connectors. See 

Table 4-1 on 

page 4-21

 for the required torque setting for each connector type.

For optimal results, terminate any unused ECal ports with a 50 ohm load.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands