Keysight Technologies 85091D Reference Manual Download Page 10

Page: 10 / 172

1-2 Electronic Calibration Modules Reference Guide

General Information
Manual Overview

— A female connector gage has a male interface so it can measure female

devices.

Accuracy of Electronic Calibration versus Mechanical Calibration

As the number of DUT test ports increases, the required number of calibration

measurements also increases. This boosts the probability of bad connections

and bad calibrations when mechanical calibration standards are used rather

than ECal. Also, test port cable repeatability and stability errors are amplified

by the increased number of connections and disconnections. To perform an

SOLT 4-port calibration, a minimum of twelve 1-port standards and three

2-port (thru) standards are measured, requiring a total of eighteen

connections. The same calibration using a 2-port ECal module (N755xA and

N469xD) requires only four connections.
Ignoring connection related errors, the following table compares the accuracy

of ECal versus mechanical calibration in various calibration options.

N755xA ECals can be used for S-parameter measurement calibrations. The

residual measurement uncertainty makes them unsuitable for advanced

applications, such as load pull, noise figure, etcetera.

Mechanical Calibration Type

ECal Thru Type

Measurement

ECal

Mechanical

Calibration

1-Port, calibration constant (

not

data-based) SOL

Reflection

1-Port, short, open, sliding load

Reflection

1-Port, data-based, expanded

Reflection

2-Port TRL

All types

Reflection

Transmission

≥

2-Port, calibration constant SOL, flush

thru

Characterized

Reflection

Transmission

Internal unknown

Reflection

Transmission

External flush

Reflection

Transmission

≥

2-Port, calibration constant SOL,

unknown thru

Characterized

Reflection

Transmission

Internal unknown

Reflection

Transmission

Summary of Contents for 85091D













































































































































































Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands

Keysight Technologies 85091D, Reference Manual

Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands