Keysight Technologies 85091D Reference Manual Download Page 108

Page: 108 / 172

5-2 Electronic Calibration Modules Reference Guide

Specifications and Characteristics
Environmental Specifications

Environmental Specifications

Operating Temperature and Accuracy Enhancement

Because the dimensions of critical components may vary over temperature,

certain electrical characteristics may change as well. Thus, the operating

temperature is a critical factor in its performance, and must be stable before

use. In addition, excessive air flow can prevent the ECal module from warming

up properly.
Measurement calibration, performance verification, and actual device

measurements must be made within

1 °C of the error-corrected operating

temperature range specification of the network analyzer. If the ambient

operating temperature drift of the network analyzer exceeds the allowable

error-corrected temperature range, a new measurement calibration must be

performed to ensure optimum accuracy.

Samples of this product have been type-tested in accordance with the

Keysight Environmental Test Manual and verified to be robust against the

environmental stresses of storage, transportation and end-use; those

stresses include but are not limited to temperature, humidity, shock,

vibration, and power-line conditions. Test methods are aligned with IEC

60068-2 and levels are similar to MIL-PRF-28800F Class 3.

Table 5-2 Environmental Specifications for all ECal Modules

Specifications

Limits

Temperature

Operating (N755xA series) - (Typical)

Operating (N469xD series)

Operating (N443xD series)

Operating (8509xD series)

Storage

Error-corrected range

15 °C to +35 °C — up to 75% RH

20 °C to +26 °C – up to 95% RH (see RH N469xD below)

20 °C to +26 °C – up to 95% RH (see RH N443xD below)

20 °C to +26 °C – up to 95% RH (see RH 8509xD below)

–40 °C to +70 °C

1 °C of measurement calibration temperature

a. Usable, but not specified from –15 to 55 °C —up to 95% RH.

Relative Humidity (N755xA)

Relative Humidity (N469xD)

Relative Humidity (N443xD)

Relative Humidity (8509xD)

<75%

Type tested, 0% to 95% at 40°C, non-condensing

Avoid prolonged handling of the module, connectors, and cables. Your

fingers are a heat source that can increase the temperature of these

devices.

Summary of Contents for 85091D













































































































































































Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands

Keysight Technologies 85091D, Reference Manual

Search results

Summary of Contents for 85091D

Reviews:

Brands by name

Popular brands