manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 127

Electronic Calibration Modules Reference Guide                                                                               5-21

Specifications and Characteristics
Mechanical Characteristics

Mechanical Characteristics

Mechanical characteristics, such as center conductor protrusion and pin 

depth, are not warranted performance specifications. They are, however, 

important supplemental characteristics related to the electrical performance of 

devices. Keysight Technologies verifies the mechanical characteristics of the 

devices with special gaging processes and electrical testing. These processes 

ensure that the device connectors do not exhibit any excess center conductor 

protrusion or improper pin depth when the module leaves the factory.

“Gaging Connectors” on page 4-9

 explains how to use pin-depth gages. Refer 

to 

“Typical Pin Depth Values” on page 5-26

 for typical and observed pin depth 

limits.

Pin Depth 

Pin depth is the distance the center conductor mating plane differs from being 

flush with the outer connector mating plane. The pin depth of a connector can 

be in one of two states: protrusion or recession. The pin depth for a 3.5 mm 

connector is shown in 

Figure 5-2

, although the description also applies to 

1.85 mm, 2.4 mm, and 2.92 mm connectors. The pin depth for 4.3–10 is shown 

in 

Figure 5-3

.The pin depth for 7–16 is shown in 

Figure 5-4

. The pin depth for 

Type-N connectors is shown in 

Figure 5-5

. Typical pin depths for ECal 

connectors are listed in 

“Typical Pin Depth Values” on page 5-26

.

Protrusion

 occurs when the center conductor extends beyond the outer 

conductor mating plane. It reads as a positive value on the connector gage. 

Recession

 occurs when the center conductor is set back from the outer 

conductor mating plane. It reads as a negative value on the gage.

No protrusion of the center conductor shoulder is allowable on any 7 mm 

connector when the slotted collet is removed. The slotted collet must be removed 

before measuring the pin depth.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands