manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 120

 5-14                                                                                Electronic Calibration Modules Reference Guide

Specifications and Characteristics
Characteristic Performance

5-

Characteristic Performance

Characteristic performance for RF and microwave ECal modules are provided 

in the following tables, which describe non-warranted performance that most 

units exhibit.

N755xA Series

Table 5-24 Characteristic Performance for N755xA (3.5 mm)

a

a. When applied power exceeds –10 dBm, calibration results will be degraded from the performance indicated in this table.

Parameter

Frequency Range

DC to 

500 MHz

500 MHz

 

to 4 GHz

4 to 6.5 

GHz

6.5 to 9 

GHz

9 to 14 

GHz

14 to 18 

GHz

18 to 26.5 

GHz

Transmission Tracking (±dB)

b

b. Values based on using the network analyzer N5234A Option 200.

0.15

0.16

0.22

0.22

0.30

0.30

0.35

Load Match (dB)

b

34

29

28

22

26

26

24

Table 5-25 Characteristic Performance for N755xA (Type-N 50

Ω

)

a

a. When applied power exceeds –10 dBm, calibration results will be degraded from the performance indicated in this table.

Parameter

Frequency Range

DC to 500 

MHz

500 MHz

 

to 4 GHz

4 to 6.5 

GHz

6.5 to 9 

GHz

9 to 14 GHz 14 to 18 

GHz

Transmission Tracking (±dB)

b

b. Values based on using the network analyzer N5234A Option 200.

0.15

0.16

0.22

0.22

0.30

0.30

Load Match (dB)

b

34

29

28

22

26

26

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands