manualshive.com logo in svg

Keysight Technologies 85091D, Reference Manual

Share
Download
Keysight Technologies 85091D Reference Manual Download Page 99

Electronic Calibration Modules Reference Guide                                                                               4-17

Use, Maintenance, and Care of the Devices
Making Connections

Making Connections

Good connections are essential for accurate calibrations and measurements 

and require a skilled operator. 

The most common cause of measurement 

error is poor connections.

1.85 mm, 3.5 mm, 2.4 mm, 2.92 mm, and Type-N Devices

1.

Handle the devices at a static-safe work station, only. See 

“Electrostatic 

Discharge” on page 4-1

.

2.

Carefully align the connectors. The male connector center pin must slip 

concentrically into the contact finger of the female connector.

3.

Push the connectors straight together and tighten the connector nut 

finger tight. Do not twist or screw the connector together. As the center 

conductors mate, there is usually a slight resistance

4.

The preliminary connection is tight enough when the mating plane 

surfaces make uniform, light contact. Do not overtighten this connection.
A connection in which the outer conductors make gentle contact at all 

points on both mating surfaces is sufficient. Very light finger pressure is 

enough to accomplish this.

5.

Make sure the connectors are properly supported. Relieve any side 

pressure on the connection from long or heavy devices or cables.

6.

Torque the connection according to the procedures described in 

“Final 

Connection Using a Torque Wrench” on page 4-18

.

7 mm Devices

Fully extend the connector sleeve on one of the connectors and fully retract 

the sleeve on the other. The extended sleeve creates a cylinder into which the 

second connector 

fi

ts.

If one of the connectors is 

fi

xed (as on a test port), fully extend that connector 

sleeve (spin its knurled connector nut to make sure the threads are fully 

extended). Fully retract the connector sleeve on the other connector.

1.

Handle the devices at a static-safe work station, only. See 

“Electrostatic 

Discharge” on page 4-1

.

2.

Remove the 7 mm collet from the center conductor with the collet 

extractor tool.1.Remove the 7 mm collet from the center conductor with 

the collet extractor tool.

3.

Carefully align the connectors.

Do not turn the device body. Only turn the connector nut. Damage to the 

center conductor can occur if the device body is twisted.

Summary of Contents for 85091D













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands