manualshive.com logo in svg

Juniper SRX3400, Hardware Manual, Page: 92 / 232

Share
Download
Juniper SRX3400 Hardware Manual Download Page 92

Figure 42: Connecting to AC Power

g036009

3.

Snap the wire bail on the power supply over the power cord to prevent the power cord
from accidentally disengaging.

4.

Insert the power cord plug into an external AC power source receptacle.

NOTE:

Each power supply must be connected to a dedicated AC power

feed and a dedicated external circuit breaker. We recommend that you
use a 15 A (250 VAC) minimum, or as permitted by local code.

5.

Dress the power cord appropriately. Verify that the power cord does not block the air
exhaust and access to services gateway components or drape where people could
trip on it.

6.

Repeat steps 1 through 5 for the remaining power supplies.

NOTE:

If power is lost to the services gateway, the Power-On/Power-Off

state is retained. For example, if the services gateway loses power while the
services gateway is on, when power returns, it will still be in the On state.

Related

Documentation

Required Tools and Parts for Grounding and Providing Power to the SRX3400 Services
Gateway on page 75

•

•

SRX3400 Services Gateway AC Power Cord Specifications on page 191

•

Grounding the SRX3400 Services Gateway on page 76

•

Connecting the SRX3400 Services Gateway to a DC Power Source on page 79

•

Powering On the SRX3400 Services Gateway on page 81

Copyright © 2013, Juniper Networks, Inc.

78

SRX3400 Services Gateway Hardware Guide

Summary of Contents for SRX3400









































































































































































































































Reviews:

No comments