Juniper SRX3400 Hardware Manual Download Page 123

Page: 123 / 232

CHAPTER 12

Replacing Hardware Components on the
SRX3400 Services Gateway

This section includes the following topics:

•

Field-Replaceable Units on the SRX3400 Services Gateway on page 109

•

Required Tools and Parts for Replacing Hardware Components on the SRX3400
Services Gateway on page 110

•

Replacing Cooling System Components on the SRX3400 Services Gateway on page 111

•

Replacing Host Subsystem Components on the SRX3400 Services Gateway on page 115

•

Replacing Power System Components on the SRX3400 Services Gateway on page 127

Field-Replaceable Units on the SRX3400 Services Gateway

Field-replaceable units (FRUs) are services gateway components that can be replaced
at the customer site. The services gateway uses the following types of FRUs:

•

Hot-swappable FRUs—You can remove and replace these components without
powering off the services gateway or disrupting the routing functions.

•

Cold-swap-only FRUs—You must power off the services gateway in order to remove,
replace, or add these components.

Table 20 on page 109

lists the FRUs for the services gateway.

Table 20: Field-Replaceable Units

Cold-Swap-Only FRUs

Hot-Swappable FRUs

Routing Engine

SFB

IOCs

NPCs

SPCs

SCM

Air filter

Fan tray

AC and DC power supplies (if redundant)

NP-IOCs

SFP, SFP+, and XFP Transceivers

109

Summary of Contents for SRX3400






















































































































































































































Search results

Summary of Contents for SRX3400

Reviews:

Juniper SRX3400, Hardware Manual, Page: 123 / 232

Search results

Summary of Contents for SRX3400

Reviews: