Juniper SRX3400 Hardware Manual Download Page 13

Page: 13 / 232

•

Join and participate in the Juniper Networks Community Forum:

www.juniper.net/company/communities

•

Open a case online in the CSC Case Manager:

www.juniper.net/cm

To verify service entitlement by product serial number, use our Serial Number Entitlement
(SNE) Tool located at

https://tools.juniper.net/SerialNumberEntitlementSearch

Opening a Case with JTAC

You can open a case with JTAC on the Web or by telephone.

•

Use the Case Manager tool in the CSC at

www.juniper.net/cm

•

Call 1-888-314-JTAC (1-888-314-5822 toll-free in the USA, Canada, and Mexico).

For international or direct-dial options in countries without toll-free numbers, visit us at

www.juniper.net/support/requesting-support.html

xiii

About This Guide

Summary of Contents for SRX3400






















































































































































































































Search results

Summary of Contents for SRX3400

Reviews:

Juniper SRX3400, Hardware Manual, Page: 13 / 232

Search results

Summary of Contents for SRX3400

Reviews: