manualshive.com logo in svg

Juniper SRX3400, Hardware Manual, Page: 28 / 232

Share
Download
Juniper SRX3400 Hardware Manual Download Page 28

•

Signal path—The midplane provides the signal path to the IOCs, SFBs, SPCs, Routing
Engine, and other services gateway components for monitoring and control of the
system.

Figure 6: Midplane

Midplane

g036068

Related

Documentation

SRX3400 Services Gateway Chassis on page 7

•

•

Available Components for the SRX3400 Services Gateway on page 9

•

SRX3400 Services Gateway Switch Fabric Board on page 14

•

SRX3400 Services Gateway Network Processing Cards on page 20

•

SRX3400 Services Gateway Services Processing Cards on page 20

SRX3400 Services Gateway Switch Fabric Board

The Switch Fabric Board (SFB) is the data plane for the subsystems in the chassis. The
SFB performs the following functions:

•

Powers the services gateway on and off

•

Controls clocking and distribution

•

Provides eight copper Gigabit Ethernet ports and four fiber Gigabit Ethernet ports

•

Provides two high availability (HA) Control ports

•

Provides interconnections to all the IOCs within the chassis through integrated switch
fabrics

•

Handles arbitration among the CFMs

•

Handles switching among multiple SPCs if present

•

Provides service ports, system LEDs, and operational buttons on the front panel

Copyright © 2013, Juniper Networks, Inc.

14

SRX3400 Services Gateway Hardware Guide

Summary of Contents for SRX3400









































































































































































































































Reviews:

No comments