manualshive.com logo in svg

Juniper SRX3400, Hardware Manual, Page: 73 / 232

Share
Download
Juniper SRX3400 Hardware Manual Download Page 73

CHAPTER 6

Installing Additional Components in the
SRX3400 Services Gateway

This section provides instructions for installing the supported cards and subsystem
components that are not pre-installed at the factory. Note that the services gateway
requires one NPC or NP-IOC and one SPC for proper operation. Additional IOCs, NP-IOCs,
NPCs, SPCs, and power supplies are optional. For detailed information about the modules
supported by the services gateway, see the

SRX1400, SRX3400, and SRX3600 Services

Gateway Module Guide

at

www.juniper.net/techpubs/

.

This section includes the following topics:

•

Installing CFM Cards in the SRX3400 Services Gateway on page 59

•

Installing SPCs in an Operating SRX3400 Services Gateway Chassis Cluster on page 62

•

Installing an SCM in the SRX3400 Services Gateway on page 65

•

Installing an AC Power Supply in the SRX3400 Services Gateway on page 66

•

Installing a DC Power Supply in the SRX3400 Services Gateway on page 69

Installing CFM Cards in the SRX3400 Services Gateway

The most common modules for the services gateway use the common form-factor
module (CFM) format:

•

IOCs

•

NP-IOCs

•

SPCs

•

NPCs

59

Copyright © 2013, Juniper Networks, Inc.

Summary of Contents for SRX3400









































































































































































































































Reviews:

No comments