manualshive.com logo in svg

Juniper SRX3400, Hardware Manual, Page: 162 / 232

Share
Download
Juniper SRX3400 Hardware Manual Download Page 162

SRX3400 Services Gateway Installation Safety Guidelines and Warnings

This section includes the following topics:

•

Chassis Lifting Guidelines on page 148

•

Installation Instructions Warning on page 148

•

Rack-Mounting Requirements and Warnings on page 149

•

Ramp Warning on page 153

Chassis Lifting Guidelines

The weight of a fully configured chassis is about 77 lb (35 kg). Observe the following
guidelines for lifting and moving the services gateway:

•

Before moving the services gateway, read the guidelines in

“SRX3400 Services Gateway

Chassis Grounding Point” on page 181

,

“Power Requirements for DC-Powered SRX3400

Services Gateways” on page 184

, and

“Power Requirements for AC-Powered SRX3400

Services Gateways” on page 189

to verify that the intended site meets the specified

power, environmental, and clearance requirements.

•

Before lifting or moving the services gateway, disconnect all external cables.

•

As when lifting any heavy object, lift most of the weight with your legs rather than your
back. Keep your knees bent and your back relatively straight and avoid twisting your
body as you lift. Balance the load evenly and be sure that your footing is solid.

•

Do not attempt to lift the chassis by the handles on the power supplies or on the
common form-factor modules (CFMs). The handles might break off and cause the
chassis to fall and inflict injury.

Related

Documentation

SRX3400 Services Gateway General Safety Guidelines and Warnings on page 141

•

•

Installation Instructions Warning on page 148

•

Rack-Mounting Requirements and Warnings on page 149

•

Ramp Warning on page 153

Installation Instructions Warning

WARNING:

Read the installation instructions before you connect the services

gateway to a power source.

Waarschuwing

Raadpleeg de installatie-aanwijzingen voordat u het systeem

met de voeding verbindt.

Varoitus

Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen.

Attention

Avant de brancher le système sur la source d'alimentation, consulter

les directives d'installation.

Copyright © 2013, Juniper Networks, Inc.

148

SRX3400 Services Gateway Hardware Guide

Summary of Contents for SRX3400









































































































































































































































Reviews:

No comments