Juniper SRX3400 Hardware Manual Download Page 64 | Manualshive

Page: 64 / 232

Juniper SRX3400 Hardware Manual Download Page 64

4.

Connect the grounding cable, as described in

“Grounding the SRX3400 Services

Gateway” on page 76

.

5.

Connect the power cables, as described in

“Connecting the SRX3400 Services Gateway

to a DC Power Source” on page 79

or

“Connecting the SRX3400 Services Gateway

to an AC Power Source” on page 77

.

6.

Power on the services gateway, as described in

“Powering On the SRX3400 Services

Gateway” on page 81

.

7.

Perform the initial system startup, as described in

“Performing Initial Software

Configuration on the SRX3400 Services Gateway” on page 86

.

Related

Documentation

SRX3400 Services Gateway Chassis on page 7

•

•

Routine Maintenance Procedures for the SRX3400 Services Gateway on page 94

SRX3400 Services Gateway Safety Requirements, Warnings, and Guidelines

To avoid harm to yourself or the services gateway as you install and maintain it, follow
the guidelines for working with and near electrical equipment, as well as the safety
procedures for working with networking devices. However, providing an exhaustive set
of guidelines for working with electrical equipment is beyond the scope of this guide.

Related

Documentation

Site Preparation Checklist for the SRX3400 Services Gateway on page 37

•

•

SRX3400 Services Gateway Definition of Safety Warning Levels on page 139

•

General Electrical Safety Guidelines and Warnings on page 163

Required Tools for Installing the SRX3400 Services Gateway

To install the services gateway, you need the following tools:

•

Mechanical lift

•

Phillips (+) screwdriver, number 2

Related

Documentation

Preparing the SRX3400 Services Gateway for Rack-Mount or Cabinet Installation on
page 51

•

•

Installing the Mounting Hardware for the SRX3400 Services Gateway on page 51

•

Installing the SRX3400 Services Gateway in a Rack or Cabinet Using a Mechanical Lift
on page 53

Copyright © 2013, Juniper Networks, Inc.

50

SRX3400 Services Gateway Hardware Guide

«
...
62
63
64
65
66
...
»

Summary of Contents for SRX3400









































































































































































































































Reviews:

No comments