Juniper SRX3400 Hardware Manual Download Page 229

Page: 229 / 232

cable, Ethernet port (for Routing Engine

management)

during initial installation......................................

tools required...........................................................

DC power and grounding cables

tools required....................................................

installing

AC power supply.............................................................

DC power supply............................................................

SCM.....................................................................................

instructions

calculation

power requirements...........................................

189

interference

electromagnetic...........................................................

196

radio frequency.............................................................

195

IOC

slot restrictions in services offload mode.............

status, checking............................................................

102

troubleshooting............................................................

102

ISHU.............................................................................................

jewelry removal warning....................................................

159

JTAC...............................................................................................

xii

Juniper Technical Assistance Center (JTAC).............

205

laser beam warning..............................................................

155

laser safety guidelines.........................................................

154

lightning activity warning...................................................

160

link loss, calculating.............................................................

198

maintaining

air filter...............................................................................

fan tray...............................................................................

host subsystem..............................................................

power supplies................................................................

modal dispersion in fiber-optic cable............................

197

mode loss, higher-order.....................................................

196

multimode fiber-optic cable

See

cable, fiber-optic

NEBS..........................................................................................

176

Network Processing I/O Card

See

NP-IOC

notice icons.................................................................................

NP-IOC........................................................................................

NPC

status, checking............................................................

104

NPCs

troubleshooting............................................................

104

operating temperature warning.......................................

161

packing services gateway

components for shipment.......................................

207

for shipment..................................................................

206

required tools and parts...........................................

206

parentheses, in syntax descriptions..................................

parts

required for packing...................................................

206

ping command........................................................................

power

budget calculation for fiber-optic cable.............

198

margin calculation.......................................................

198

requirements for hardware components............

189

surges...............................................................................

196

power supplies

AC electrical specifications......................................

188

DC electrical specifications......................................

184

maintaining.......................................................................

power system

AC electrical specifications......................................

188

troubleshooting............................................................

106

powering off the services gateway..................................

powering on the services gateway....................................

product disposal warning..................................................

162

qualified personnel warning..............................................

142

rack

clearance around, required.........................................

mounting bracket hole spacing.................................

securing to building.......................................................

size and strength required..........................................

standards, EIA and ETSI.............................................

rack requirements

mounting.........................................................................

149

radiation from open port apertures warning..............

156

radio frequency interference, preventing.....................

195

relative humidity, acceptable............................................

179

repair policies.........................................................................

202

215

Index

Summary of Contents for SRX3400






















































































































































































































Search results

Summary of Contents for SRX3400

Reviews:

Juniper SRX3400, Hardware Manual, Page: 229 / 232

Search results

Summary of Contents for SRX3400

Reviews: