Home
/
Juniper
/
SRX3400
/
Hardware Manual

Juniper SRX3400, Hardware Manual, Page: 143 / 232

Share

Page: 143 / 232

Juniper SRX3400 Hardware Manual Download Page 143

Figure 60: Removing an AC Power Supply

g036018

5.

Orient the replacement power supply so that the tab is on the left side, as shown in

Figure 61 on page 129

.

Figure 61: Inserting an AC Power Supply

g036017

6.

Using both hands, slide the replacement power supply straight into the chassis until
the power supply is fully seated in the chassis slot. Make sure the tab on the left edge
of the power supply clicks into place. The power supply faceplate should be flush
with any adjacent power supply faceplate.

NOTE:

Be sure to have the power supply oriented correctly. The tab must

be on the left and click into place when fully seated. If the power supply
does not insert easily or does not become flush with the chassis, you might
have inserted the power supply upside down.

7.

Attach the power cord to the power supply. If the power supply is correctly installed
and functioning normally, the power supply powers up immediately.

129

Copyright © 2013, Juniper Networks, Inc.

Chapter 12: Replacing Hardware Components on the SRX3400 Services Gateway

«
...
141
142
143
144
145
...
»

Summary of Contents for SRX3400









































































































































































































































Reviews:

No comments