Juniper SRX3400 Hardware Manual Download Page 26

Page: 26 / 232

Table 7: Allowed Slot Locations for the SRX3400 Services Gateway
Components

Allowed Slot Locations

Module Name

Front slot labeled

SFB

Rear slot labeled

RE0

Routing Engine

Rear slot labeled

RE1

SCM

Front slots labeled

IOCs

Front slots labeled

and rear slots labeled

. We recommend

that you install NP-IOCs in front panel slots to simplify cable
management.

NP-IOCs

Rear slots labeled

NPCs

Front slots labeled

and rear slots labeled

SPCs

Rear slots (two) on bottom left of chassis.

Power supplies

Rear, vertical slot on far right of chassis.

Fan tray and air filter

Figure 4: Front Slots on the SRX3400 Services Gateway

g036118

SFB

Slot 1
SPC, IOC, or NP-IOC

Slot 3
SPC, IOC, or NP-IOC

Slot 2
SPC, IOC, or NP-IOC

Slot 4
SPC, IOC, or NP-IOC

Figure 5: Rear Slots on the SRX3400 Services Gateway

g036119

Routing Engine
in slot RE0

Power supplies

Slot 5
SPC, NPC, or NP-IOC

Slot 6
SPC, NPC, or NP-IOC

Slot 7
SPC, NPC, or NP-IOC

Fan tray and air filter
(behind door)

Slot RE1 for SCM

SRX3400 Services Gateway Hardware Guide

Summary of Contents for SRX3400






















































































































































































































Search results

Summary of Contents for SRX3400

Reviews:

Juniper SRX3400, Hardware Manual, Page: 26 / 232

Search results

Summary of Contents for SRX3400

Reviews: